Technical Specifications
Typical physical property data, subject to batch test reports.
| No | Test Item | Unit | Typical Value (YT-4501N) | |
|---|---|---|---|---|
| 1 | Appearance | - | Compliance | |
| 2 | Density | g/cm³ | 1.39 | |
| 3 | Shore Hardness | A | 88 | |
| 4 | Original Tensile Strength | MPa | 12 | |
| 5 | Original Elongation at Break | % | 350 | |
| 6 | Ageing | Test Condition | - | 175℃*240h |
| Variation of Tensile Strength | % | +15 | ||
| Variation of Elongation at Break | % | -10 | ||
| 7 | With copper ageing 150℃±2℃×3000h | - | No brittleness | |
| 8 | Low-Temperature Impact | Test Condition | - | -40℃ |
| Failure (≤15/30) | Piece | 0 | ||
| 9 | Oxygen Index | % | 33 | |
| 10 | Volume Resistivity (20℃) | Ωm | 5*10¹² | |
| 11 | Dielectric Strength (20℃) | MV/m | 27 | |
| 12 | Hot Set Test | Test Condition | - | 200℃ 0.2MPa 15min |
| Elongation under load | % | 35 | ||
| Permanent deformation after cooling | % | 0 | ||
| 13 | Smoke Density | With Flame | Ds max | 310 |
| Without Flame | Ds max | 85 | ||
| 14 | The gas when it burns | HCl and HBr Content | % | 0 |
| HF Content | % | 0 | ||
| pH Value | - | 5.9 | ||
| Conductivity | μs/mm | 1.0 |
Extrusion Process
Mixing: Before using this product, mix components A and B evenly and then add them to the hopper. If color is needed, it is recommended to use color masterbatch based on EVA (the masterbatch must be dried). It is advised to use the material within 8 hours after opening the package, and drying the material is prohibited. During the mixing process of components A and B, be careful to prevent external moisture from being introduced.
Screw Type: Optimal compression ratio for the screw: 1.5±0.2
Pay-off Speed: Without the effect of smoothness and performance, the faster,the better
Crosslinking process: After the wire is formed, it can be naturally crosslinked or crosslinked in a water bath (steam). Natural crosslinking: at room temperature of 15-25°C, crosslinking can be completed within a week; at temperatures above 25°C, crosslinking can be completed within three days. If water bath or steam crosslinking is used, to prevent cable adhesion, the water bath (steam) temperature should be controlled at 60°C-70°C and crosslinking can be completed in about 4 hours. The above crosslinking times are based on an insulation thickness of ≤1mm; if the thickness exceeds this, the specific crosslinking time should be adjusted according to the product thickness and degree of crosslinking to meet cable performance specifications. Full performance testing should be conducted, with water bath (steam) at 50°C and boiling time greater than 8 hours, to ensure the material is fully crosslinked.
Extrusion Temperature:It is recommended to control the melt temperature at 160±10°C, and the final extrusion temperature should be adjusted based on the actual situation.
| Zone 1 | Zone 2 | Zone 3 | Zone 4 | Neck | Head |
|---|---|---|---|---|---|
| 100±10 | 125±10 | 135±10 | 135±10 | 140±10 | 150±10 |
Packaging and storage
- 1.Package:Packed by aluminium foil bag.
- 2.Transportation: It should not be exposed to sun, rain, or mechanical damage.
- 3.Storage: Should be stacked in a clean and dry warehouse, Shelf life: 6 months.



